Hmm , let's see here. Chunky toothpaste looking welds and cheesy rear axle setup. I'm going to guess it's one of the Terminator Scooter models. If only there was some way to tell.
terminators? ive had nothing but good luck w/the 3 i own(2pockets 1chopper)yes the chop.has a lot of plastic crap on it,but all 3 have good welds,and the frames are strit.i looked at an origami a while back that looked like ray charles welded it,just repaired a rsa with a bent frame,rear arm was3/4 off.
My Terminator cag has welds there they didn't even line up the tubes before welding. It has horrible welds in most other places. Mine even has pieces of welding wire sticking up 1/2 inch.
Where can you get parts for a Terminator . I work on big bikes but the lil ones are fun this is for my lil girl . I just want to replace the rings id like to put a new carb on 2 but we will see again its for a lil girl who is 10 . Thanks guys for all the hlep.
It's hard to tell which engine is in there with all the plastic in the way, but I would try Dave's motors as it looks kinda like a go-ped style engine. the link is on the main page of this forum. Look around Dave's web site.
you could also email terminator scooters afterservice@terminatorscooter.com
its me again!you can get rings for em at just about any lawnmower shops around,you will need to bring in the old ones and match em to the new set.my bikes are sold thru a company named goldenvale-roketa/phone em at 1-800-520-9811;or1-800-969-7771,the music they play while your on hold is worth it alone.1 more thing let us know what numbers or letters are on the base of the head,on the left side.
its me again!you can get rings for em at just about any lawnmower shops around,you will need to bring in the old ones and match em to the new set.my bikes are sold thru a company named goldenvale-roketa/phone em at 1-800-520-9811;or1-800-969-7771,the music they play while your on hold is worth it alone.1 more thing let us know what numbers or letters are on the base of the head,on the left side.
Hows it going i was just wondering how can u tell what it is by the nums or letters.Are you talking about the ones on the fly wheel casing or the ones at the bottom of the barrel. Cheers
heres mine, its 110cc 4 stroke, 4 speed, runs on alcahol. gets the front wheel up pretty easy, it rips around around pretty quick, only beef that i have is that it raps out too fast, i need to gear it up some. been having a hard getting some sprockets.
shouldnt be a problem to get sprockets for it. with that set up you should be able to take it to a regular bike shop and have them match up the bolt pattern and then get you a bigger rear sprocket, also check for a rev limiter, if there is a manual one, remove it otherwise there are chips you can install to fix that .
the problem with the rear sprocket, is that if i go much smaller my sprocket will smaller than where it mounts to the wheel and the chain will hit the rim, as far as the front, i think i have an 11 tooth, but i have a 14 tooth at the house that i need to try.
I have a work in progress chopper. Its one of the 49cc choppers with the plastic vtwin, but I took the original motor out and replaced it with a 16 Horsepower Kohler V-twin. I have no pics at the moment, but I will probably post some soon. I have no idea what it is going to do, but I know I need to brace the HELL out of the Frame!
I work on big bikes but the lil ones are fun this is for my lil girl . I just want to replace the rings id like to put a new carb on 2 but we will see again its for a lil girl who is 10 . Thanks guys for all the hlep.
