Pocketbike Forum banner

x15 help please

2432 Views 28 Replies 5 Participants Last post by  CAM2
I need help with thus problem please. Here it is, when am riding it, it tends to slow down when I give it more gas. It also feels like its not going as fast as it was before. I asking turned the a/f mixture screw out 2 turns. Could it be the idle screw or probably my throttle cable?
1 - 20 of 29 Posts
Turn the a/f mix screw to 3 turns out and set the c-clip to the 4th notch
Turn the a/f mix screw to 3 turns out and set the c-clip to the 4th notch
Alright am gunna turn it out 3 turns but here's where I need help .you've told me before about the c-clip but I have no idea where it is an how to do it? Pictures help out a lot:)
Thanks!
Alright am gunna turn it out 3 turns but here's where I need help .you've told me before about the c-clip but I have no idea where it is an how to do it? Pictures help out a lot:)
Thanks!
Hey can you post a pic of your carb from all 4 directions please,I need to see something
Hey can you post a pic of your carb from all 4 directions please,I need to see something
There coming up
2
Alright am gunna turn it out 3 turns but here's where I need help .you've told me before about the c-clip but I have no idea where it is an how to do it? Pictures help out a lot:)
Thanks!


See less See more
So where the picture showed its on the 2 notch. Do I just move it two down? And that will be the 4th?
So where the picture showed its on the 2 notch. Do I just move it two down? And that will be the 4th?
The red line from the listing points to the second notch....Theres two ends on the needle.... blunt end and pointy end.......from the blunt top to the pointy tip... the notches go from 1 to 5...1 being the leanest fuel setting and 5 being the richest setting.............
hey, so it was good at one time but now it slows at full throttle, if you didnt change the pipe or airfilter then id say your main and pilot jets are getting clogged, maybe not enough for it not to run but when they slowly cake up with this ethanol thats what ya get, clean your jets and tube and your good
hey, so it was good at one time but now it slows at full throttle, if you didnt change the pipe or airfilter then id say your main and pilot jets are getting clogged, maybe not enough for it not to run but when they slowly cake up with this ethanol thats what ya get, clean your jets and tube and your good
Ima try that thanks!
Everyday I wake up I smell gas in my garage and find my gas tank empty when it full the night before! What the heck! I notice its coming out of the overflow.
Earlier that day I turned it on but I didn't have the gas cover on to see if it leaks while its running and when I gave it gas a lot of gas it started squirting out from a hole in the right side of the Carb is that normal? I don't have nothing plugged into that hole
Remove your gastank and wash it out with hot soapy water and replace the fuellines and fuelfilter to 1/4" then clean the carb out good....You may be recontaminating the carb with trash from the tank/fuellines.......
Remove your gastank and wash it out with hot soapy water and replace the fuellines and fuelfilter to 1/4" then clean the carb out good....You may be recontaminating the carb with trash from the tank/fuellines.......
I already have done that but the problem still active. And I cleaned the Carb inside and jets
Then it's got to be a problem with the needle and seat, and/or the float.
Then it's got to be a problem with the needle and seat, and/or the float.
What is the seat?
It is where the fuel inlet needle (NOT the one on the slide) seals to prevent excess fuel from entering the bowl.

Watch this video. It is not the same exact carb, but all the concepts are the same.

http://www.youtube.com/watch?v=a5p6YScsTNQ

He talks about the needle and seat starting at ~2:30
So I am opening up my Carb right now to clean it again and I am going to post picturess to see if float is set right and everything seems fine..
is this hole suppose to be open?
http://i1064.photobucket.com/albums/u368/sky210v/2012-08-03145504.jpg
So I am opening up my Carb right now to clean it again and I am going to post picturess to see if float is set right and everything seems fine..
is this hole suppose to be open?
http://i1064.photobucket.com/albums/u368/sky210v/2012-08-03145504.jpg
Yeah but its supposed to have an overflow hose on it..........
1 - 20 of 29 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top